Magtek USB INSERTION READER Manual de usuario

USB INSERTION READER TECHNICAL REFERENCE MANUAL Manual Part Number 99875205 Rev 13 MAY 2012 REGISTERED TO ISO 9001:2008 1710 A

USB Insertion Reader 2 FEATURES Major features of the Insert Reader are as follows: • Powered through the USB – no external power supply required

Section 1. Features and Specifications 3 ACCESSORIES The accessories are as follows: Part Number Description 16051430 Cable, USB- A to mini USB-

USB Insertion Reader 4 SPECIFICATIONS Table 1-2 lists the specifications for the Insertion Reader. Table 1-2. Specifications * ISO (Internationa

5 SECTION 2. INSTALLATION This section describes the cable connections, the Windows Plug and Play Setup, and the physical mounting of the unit. U

USB Insertion Reader 6 Figure 2-2. Connector Location for 3-track Models The 5-pin connections between the Reader and the USB connector shown in

Section 2. Installation 7 WINDOWS PLUG AND PLAY SETUP On hosts with the Windows operating system, the first time the device is plugged into a sp

USB Insertion Reader 8 Figure 2-3. MagTek Bezel Mounting Dimensions

Section 2. Installation 9 CARD INSERTION AND ORIENTATION The Reader can be mounted in two positions as shown in Figure 2-3. On the left panel o

USB Insertion Reader 10

11 SECTION 3. OPERATION This section describes the card reading operation. CARD READ A card may be read by inserting it into the reader slot or r

ii Copyright© 2001-2012 MagTek®, Inc. Printed in the United States of America Information in this document is subject to change without notice. No

USB Insertion Reader 12

13 SECTION 4. USB COMMUNICATIONS (HID) The Reader can be operated in two different modes: • HID (herein referred to as “HID mode”) and • HID wit

USB Insertion Reader 14 The device will go into suspend mode when directed to do so by the host. The device will wakeup from suspend mode when dir

Section 4. USB Communications (HID) 15 REPORT DESCRIPTOR The HID report descriptor is structured as follows: Item Value(Hex) Usage Page (Magne

USB Insertion Reader 16 Offset Usage Name 0 Track 1 decode status 1 Track 2 decode status 2 Track 3 decode status 3 Track 1 data length 4 Tr

Section 4. USB Communications (HID) 17 TRACK 1 DATA LENGTH This one byte value indicates how many bytes of decoded card data are in the track 1

USB Insertion Reader 18 TRACK 1 DATA This field contains the decoded track data for track 1. TRACK 2 DATA This field contains the decoded track da

Section 4. USB Communications (HID) 19 COMMAND NUMBER This one byte field contains the value of the requested command number. The following tab

USB Insertion Reader 20 Get Property Response Data: Data Offset Value 0 – n Property Value Set Property Request Data: Data Offset Value 0 Propert

Section 4. USB Communications (HID) 21 Example Get Software ID property Request (Hex): Cmd Num Data Len Prp ID 00 01 00 Example Get Software ID

iii LIMITED WARRANTY MagTek warrants that the products sold pursuant to this Agreement will perform in accordance with MagTek’s published specificat

USB Insertion Reader 22 POLLING INTERVAL PROPERTY Property ID: 2 Property Type: Byte Length: 1 byte Get Property: Yes Set Property: Ye

Section 4. USB Communications (HID) 23 MSR DIRECTION PROPERTY Property ID: 3 Property Type: Byte Length: 1 byte Get Property: Yes Set

USB Insertion Reader 24 CARD INSERTED PROPERTY Property ID: 4 Property Type: Byte Length: 1 byte Get Property: Yes Set Property: No De

Section 4. USB Communications (HID) 25 Example Set Max Packet Size property Request (Hex): Cmd Num Data Len Prp ID Prp Value 01 02 05 20 Exampl

USB Insertion Reader 26 Example Get Interface Type property Request (Hex): Cmd Num Data Len Prp ID 00 01 10 Example Get Interface Type property Re

Section 4. USB Communications (HID) 27 RESET DEVICE COMMAND Command number: 2 Description: This command is used to reset the device. This com

USB Insertion Reader 28

29 SECTION 5. USB COMMUNICATIONS (KB) The Reader can be operated in two different modes: • HID (herein referred to as “HID mode”) and • HID with

USB Insertion Reader 30 CARD DATA The card data is converted to ASCII and transmitted to the host as if it had been typed on a keyboard. Any data

Section 5. USB Communications (KB) 31 where: ES = P22 (end sentinel) LRC = Longitudinal redundancy check character P5 = Terminating charac

iv FCC WARNING STATEMENT This equipment has been tested and was found to comply with the limits for a Class B digital device pursuant to Part 15 of

USB Insertion Reader 32 HID USAGES HID devices send data in reports. Elements of data in a report are identified by unique identifiers called usag

Section 5. USB Communications (KB) 33 REPORT DESCRIPTOR The HID report descriptor is structured as follows: Item Value(Hex) Usage Page (Generic

USB Insertion Reader 34 COMMANDS Command requests and responses are sent to and received from the device using feature reports. Command requests a

Section 5. USB Communications (KB) 35 RESULT CODE This one-byte field contains the value of the result code. There are two types of result code

USB Insertion Reader 36 Property ID is a one-byte field that contains a value that identifies the property. The following table lists all the curr

Section 5. USB Communications (KB) 37 Set Property: No Description: This is an 11 byte read only property that identifies the software part nu

USB Insertion Reader 38 POLLING INTERVAL PROPERTY Property ID: 2 Property Type: Byte Length: 1 byte Get Property: Yes Set Property: Yes Defaul

Section 5. USB Communications (KB) 39 TRACK ID ENBLE PROPERTY Property ID: 27 (0x1B) Property Type: Byte Length: 1 byte Get Property: Yes Se

USB Insertion Reader 40 Description: This property is defined as follows: ICL SS ES LRC 0 LC Er Er ICL 0 – Changing the state of the ca

Section 5. USB Communications (KB) 41 c 1-127 – 7 bit ASCII char code 0 – send nothing This property is stored in non-volatile memory,

v TABLE OF CONTENTS SECTION 1. FEATURES AND SPECIFICATIONS ...

USB Insertion Reader 42 Default Value: 0x23 ‘#’ Description: This character is sent as the track 3 start sentinel for cards that have track 3 enc

Section 5. USB Communications (KB) 43 POST CARD CHAR PROPERTY Property ID: 12 (0x0C) Property Type: Byte Length: 1 byte Get Property: Yes Se

USB Insertion Reader 44 ASCII TO KEYPRESS CONVERSION TYPE PROPERTY Property ID: 15 (0x0F) Property Type: Byte Length: 1 byte Get Property: Yes

Section 5. USB Communications (KB) 45 Example Get ASCII to Keypress Conversion Type property Response (Hex): Result Code Data Len Prp Value 00 0

USB Insertion Reader 46 ACTIVE KEYMAP PROPERTY Property ID: 17 (0x11) Property Type: Byte Length: 1 byte Get Property: Yes Set Property: Yes D

Section 5. USB Communications (KB) 47 PRE CARD STRING PROPERTY Property ID: 18 (0x12) Property Type: String Length: 0 – 7 bytes Get Property:

USB Insertion Reader 48 Example Set Post Card String property Response (Hex): Result Code Data Len Data 00 00 Example Get Post Card String prope

Section 5. USB Communications (KB) 49 ES PROPERTY Property ID: 22 (0x16) Property Type: Byte Length: 1 byte Get Property: Yes Set Property:

USB Insertion Reader 50 Example Get MSR Direction property Response (Hex): Result Code Data Len Prp Value 00 01 02 CARD INSERTED PROPERTY Property

Section 5. USB Communications (KB) 51 Example Set Sensor Blocked Char property Response (Hex): Result Code Data Len Data 00 00 Example Get Sen

vi SOFTWARE ID PROPERTY ... 36 SERIAL

USB Insertion Reader 52 Get Property: Yes Set Property: Yes Default Value: 0xFF (use ES property) Description: This character is sent as the en

Section 5. USB Communications (KB) 53 RESET DEVICE COMMAND Command number: 2 Description: This command is used to reset the device. This comm

USB Insertion Reader 54 When both the key usage ID and the key modifier byte are set to 0xFF for a given ASCII value, the ALT ASCII code is sent

Section 5. USB Communications (KB) 55 SET KEYMAP ITEM COMMAND Command number: 4 Description: This command is used to set a key map item of the

USB Insertion Reader 56 Data structure: Request Data: Offset Field Name Description 0 ASCII value Value of the ASCII character to be set in the key

Section 5. USB Communications (KB) 57 SAVE CUSTOM KEYMAP COMMAND Command number: 5 Description: This command is used to save the active key ma

USB Insertion Reader 58

59 SECTION 6. DEMO PROGRAM The demo program, which is written in Visual Basic, can be used to do the following: • Send command requests to the d

USB Insertion Reader 60 • To send commands to the device, click the Send Commands tab (if not already selected). • Enter a command in the Messag

61 APPENDIX A. USAGE ID DEFINITIONS This appendix is from the following document found on www.usb.org: Universal Serial Bus HID Usage Tables, Ver

vii TABLES AND FIGURES Figure 1-1. USB Insertion Reader ...

USB Insertion Reader 62 Usage ID (Dec) Usage ID (Hex) Usage Name Ref: Typical AT-101 Position PC-AT Mac UNIX Boot 18 12 Keyboard o and O4 25 √ √

Appendix A. Usage ID Definitions 63 Usage ID (Dec) Usage ID (Hex) Usage Name Ref: Typical AT-101 Position PC-AT Mac UNIX Boot 59 3B Keyboard F2

USB Insertion Reader 64 Usage ID (Dec) Usage ID (Hex) Usage Name Ref: Typical AT-101 Position PC-AT Mac UNIX Boot 101 65 Keyboard Application10 129

Appendix A. Usage ID Definitions 65 Usage ID (Dec) Usage ID (Hex) Usage Name Ref: Typical AT-101 Position PC-AT Mac UNIX Boot 143 8F Keyboard In

USB Insertion Reader 66 Usage ID (Dec) Usage ID (Hex) Usage Name Ref: Typical AT-101 Position PC-AT Mac UNIX Boot 195 C3 Keypad ^ 196 C4 Keypa

Appendix A. Usage ID Definitions 67 Footnotes 1. Usage of keys is not modified by the state of the Control, Alt, Shift or Num Lock keys. That

USB Insertion Reader 68

69 APPENDIX B. MODIFIER BYTE DEFINITIONS This appendix is from the following document found on www.usb.org: Device Class Definition for Human Int

USB Insertion Reader 70

71 APPENDIX C. BEZEL DESIGN The engineering drawings in this section are for customers interested in designing their own bezel. The example shown

viii Figure 1-1. USB Insertion Reader

USB Insertion Reader 72 Figure C-1. Dimensions for Bezel Design Sheet 1

Appendix C. Bezel Design 73 Figure C-2. Dimensions for Bezel Design Sheet 2

1 SECTION 1. FEATURES AND SPECIFICATIONS The USB (Universal Serial Bus) HID (Human Interface Device) Insertion Reader is a compact magnetic stripe